How To Successfully Weld Aluminum with a Compact MIG Welder

When it comes to welding aluminum items around the home or garage, there are a few misconceptions we hope to clear up: 1) That you need to invest in a $4,000 welding machine and be highly skilled to have success; 2) With no practice you can make excellent welds the first time the wire feed welder is taken out of the box; and 3) You need an expensive spool gun suited for aluminum.

The truth is that with practice, the right equipment and proper set-up, a compact MIG welder will be able to tackle occasional aluminum welding jobs. Using your MIG welder, you will be able to work on a variety of items around your home and yard, such as grills, railings, backyard furniture, boat docks and even decorative elements. Compact MIG welders, such as the SP, Weld-Pak or Pro models from Lincoln Electric, are available at distributors and retail outlets.

A Word About Aluminum
Even home welding enthusiasts who have experience welding steel may find a switch to aluminum challenging. Here's why: Because of the softness of aluminum wire, it is more difficult to feed. In addition, wire diameters and machine settings normally used for steel may not be appropriate for aluminum. In order to be successful, ask yourself these questions:

What Machine Do I Need?
The first decision is what type of machine is right for the job. Keep in mind that a 115 volt wire feeder welder can handle jobs that range from 22 to 12 gauge and with moderate preheating, you can probably weld as thick as 1/8". Be aware that preheating should be limited to 250 degrees F maximum.

Another option is a 230 volt machine which can weld from 22 gauge all the way to 3/16". Proper preheat can take the range to 1/4". If you will need to weld a broader range of aluminum thicknesses, consider investing in the 230v machine.

Remember, if you plan on doing regular aluminum fabrication, you will need a heavy duty machine. The 115 volt and 230 volt compact MIG welder models are acceptable for occasional aluminum jobs, but not recommended for heavy duty aluminum use. For daily production welding on heavier aluminum, consider a welder that has greater than 200 amps output.

After you have chosen your input voltage, another common question you will be asked when selecting a welder is whether you want a continuous or tapped voltage control model.

A continuous voltage control model lets you set an infinite range of voltage within the rating of the machine, allowing more adjustability, fine tuning and precise control. This permits you to more easily adapt the voltage to your application and particular skill level.

If you're on a budget, opt for the tapped control unit. This machine has a rotary switch with four or five fixed voltage choices. It will not give you the control of a continuous model, but it can be slightly easier to get up to speed with and costs less to purchase and will be adequate for most applications.

What Type of Welds Can be Made?
For these types of machines, it is best to make welds in the horizontal and flat positions. In general, fillet welds in lap joints are made more easily than groove welds in butt joints. Fillet welds in tee joints are preferred over corner joints. Keep in mind that home welding by an amateur is not recommended for critical welds where failure could result in serious injury.

What Type of Shielding Gas is Required?
MIG welding aluminum is different than welding steel when it comes to shielding gas requirements. For aluminum, 100 percent argon is the gas of choice, whereas steel welding calls for a mixed gas or 100 percent CO2 gas. The good news is that no special equipment is needed - your existing regulators (with the exception of CO2 regulators) and gas hoses can be used for both pure blends and mixed gases.

What Polarity Setting is Needed?
All MIG welding, including on aluminum materials, requires electrode positive polarity, while flux-cored processes typically use electrode negative. If you are switching your wire feed welder between processes, make sure to switch your polarity. This is a common mistake that many beginning welders make.

What Aluminum Wire Electrode Alloy Type Should I Buy?
You will not obtain good results attempting to weld on aluminum with a steel wire electrode.

Instead, our recommendation is that compact MIG welders should be limited to .035" diameter 4043 aluminum alloy filler metal. A 5356 aluminum alloy electrode may commonly be recommended by retailers and distributors, since it is a stiffer wire and can be easier to feed. However, with these types of wire feed welders, there is often not enough amperage to achieve a good weld with 5356. Even though 4043 is a softer wire, following the proper steps outlined below will ensure good feedability.

Do not use other diameter wires. Specifically, you should avoid 0.030" wire (it is difficult to feed) and 3/64" wire (these compact machines do not typically produce enough current to reliably melt this diameter of wire).

How Do I Set-Up My Machine to Weld Aluminum?
Now that you know the type of machine you want and its capabilities/limitations, it is important to know how best to set it up. Follow these tips:

Purchase an Aluminum Feeding Kit
Attention to feeding issues is much more critical when it comes to aluminum welding. It is highly recommended that you purchase an aluminum feeding kit, which includes the following items:

    Non-metallic liner - designed to minimize the amount of friction on the wire
    U-shaped drive rolls - to avoid crushing or deforming the soft aluminum wire. These drive rolls do not shave the wire like V-groove drive rolls. Using V-groove drive rolls, the resulting wire shavings can clog the liner and lead to feeding problems.
    Inlet and outlet guides - designed specifically to avoid wire shaving.
    Contact tips - as compared to those used for the same diameter of steel wire electrode, contact tips for aluminum have larger diameter holes, since as aluminum heats up, it expands more than steel. Therefore, contact tips for aluminum applications are sized small enough to maintain good electrical contact, but large enough to allow for expansion.

Load Wire Into the Machine
There is a trick to properly loading aluminum wire into a wire feed welder. While the same technique should be used with steel wire electrodes, it is especially important with aluminum wire loading, to avoid feeding problems during welding.